In 2022, you still won't install the lace closure? look here

How To Install a Lace Closure?

Every girl's dream is to have hair that can adopt desired hairstyles. So hair experts design different hair extensions which are made of human hair And free from chemicals. Using these hair extensions, you can quickly create any hairstyles which suit your outfit.

And to give a natural look to these hair extensions after wearing them closure is designed. To provide the perfect natural hair look to extensions that you are using it is important to follow the correct steps for closure installation.

What Is Lace Closure?

Lace closures are hairpieces where hair strands are tied on a beige or dark brown lace. Remy lace closures are a few inches wide and they are applied where the hair would have been left to give a natural look on heads that have wigs on. Lace closures sew in have visible knots and a stretcher base.

Why Choose Lace Closure?

The advantages of using hair closures are that they always look realistic and some are arranged with baby hair at the front to simulate the growth of your natural hairline. They cause minimal or no damage to your natural hair and hence are a danger-free addition. These hair closures are also great because they can vary from small to big, but they are almost always applied in small patches. You can go to a hairdresser or do it yourself at home and the result will always be stunning no matter what.

How to install lace closure or front?

Step 1: Get your wig ready.

We can say that hair extensions can enhance your style and beautify your facial features, so wear them with confidence. You have to wash and condition it carefully, and occasionally take your wig to a stylist and style it the way you like it.

Step 2: Do a skin test.

Because some people are allergic to the chemicals used to hold wigs in place, you should get a skin test to determine if you are allergic. First, apply a small amount of liquid adhesive or double-sided wig tape to the back of your hand. Next, observe the adhesive for at least twenty-four hours. If your skin becomes red or inflamed, buy a hypoallergenic wig or adhesive instead. You can safely wear the wig while your skin is not affected.

Step 3: Flatten the hair.

It is said that the flatter the hair rests on the head, the better the wig will look. In this step, you can braid your short hair or attach it to your head using gel and bobby pins. If you have long hair, tie it into a low ponytail. After that, wrap the ponytail into a flat bun and secure with bobby pins. Also, you can use any gel or hairspray to dry before continuing.

Step 4: Put on the wig cap.

As we have seen, wig caps or stocking caps are soft caps that flatten the hair and help the wig stay in place. Next gently pull on the stocking cap, being careful not to disturb your flat hair. In the next step, you should adjust the hat so that it barely covers your hairline. Skip this step if your hair is thin and short. The hat, on the other hand, slides over your head and gathers under your wig. Also, you should make sure all your hair is tucked into this hat, even the hair on the back of your neck.

Step 5: Cleanse your hairline skin.

At this stage, wash the skin with a mild cleanser, making sure the application area is oil-free, then blot dry with a towel. Next, put some rubbing alcohol on a cotton ball and rub it along your hairline, which will remove excess oil from your skin. Spray the scalp protectant directly on the head to act as a barrier between the skin and the adhesive. Let the serum dry completely before continuing. Scalp protection serums can be purchased at wig supply stores and online.

Step 6: Test the fit of the wig.

Before using any adhesive, you need to make sure the wig fits properly. You must wear the wig on your head and align it with your natural hairline. If the wig has tightening straps inside, you may need to adjust these to fit. If the wig does not fit properly and does not have any tightening straps, you must contact the manufacturer for assistance. Also, if you can feel a strong pressure ring around the scalp, the wig is too tight. You have to remember to loosen the straps slightly. Conversely, if the wig slides side to side when you move your head, the wig is too loose. All you should do is tighten the straps.

Step 7: Trim Lace.

When your wig fits properly, you must trim the lace on the Front Lace Wig. This only needs to be done the first time you use the wig, not if the lace has been trimmed by the manufacturer. Use a few buttons to pull the hair far away from your face. Next, using sharp pink scissors, trim the lace along your natural hairline. You should be left with about 1/8" (3mm) of lace. This is a must when you put on a wig for the first time.

Step 8: Remove the wig and set it aside.

During this step, carefully pull down the wig, leaving all the clips behind, and lay the wig on a clean, flat surface. Also, you have to arrange the wig so that it is easy to see the part on the hairline as well as the part at the nape. And you have to know that if you have to loosen any straps to remove the wig, your wig is too tight.

Step 9: Attach the wig strap.

Applying wig straps - how to install lace closure or front?

First, cut six to ten small pieces of the wig. Second, line your hairline with little tape by pressing the sticky side against the skin. Next, use a mirror as you do this to create an even hairline. After that, after applying the tape, remove the thick foam pad to expose the other side of the tape. Unless you make sure all parts are touching, you may have loose gaps in your hairline.

Step 10: Apply Liquid Adhesive.

It is said that if you don't want to use a wig, you can use liquid lace glue instead. At this stage, you just use the brush to apply the adhesive to the area where the wig will be attached. You can then use a cold air setting and blow dry the adhesive for about 30 seconds. In this case, you can use a soft adhesive and let the glue dry long enough to become tacky before using the wig. On the other hand, if you use a hard adhesive, you can use the wig right away.

Step 11: Put on the wig.

This step will show you how to put on the wig carefully. First, adjust the edges of the wig so that the hairline matches. Second, adjust the back of the wig so that it hangs naturally over the hair. Finally, press the wig's lace into the adhesive or wig band. When you press the lace into the adhesive or wig band, it can be difficult to remove, so you must make sure the wig is perfectly aligned before doing so.

Step 12: Style Your Hair.

Style your hair - how to install a lace closure or front?

Unless your wig is made from human hair, you can't use regular brushes, heat styling tools, and hair products. Instead, your wig is synthetic and avoid regular brushes and thermal styling tools. So use a wide-toothed comb or wig brush to condition your hair.

Lace closures are hair pieces with hair tied to a piece of lace. More and more women invest in a lace closure instead of using the traditional method which gives them the ability to part their hair in the front.

A lot of people want to try lace closures but are worried about how they would look. If you can’t afford to get a professional to install it, you could do it yourself after doing your own research. Good luck!